Etanol.nu

Forum för föreningen etanol.nu
Aktuellt datum och tid: tor 24-03-28 11:01

Alla tidsangivelser är UTC + 1 timme




Ny tråd Svara på tråd  [ 1 inlägg ] 
Författare Meddelande
InläggPostat: sön 08-06-15 13:49 
Offline
Forummoderator

Blev medlem: mån 07-01-01 20:57
Inlägg: 6015
Ort: Hindås
HIttade till slut korrekta utdrag på nätet gällande alla felkoder man kan få ut , såväl med LED blinkmojäng ( fungerar upp tom ÅM 1994),
(Här hur man bygger en enkelt: http://pages.prodigy.net/jforgione/MB_X11.html
Längst ned på sidan: "Home Brew DTC Tool")
, som med databurk (HHT =Mercedes egna Hand Held Tester, eller t.ex. usb-baserade program som CarSoft eller liknande):
http://tinyurl.com/4fwus7

(Originalet ligger här:
http://tech.bentleypublishers.com/servl ... /download/
30191-294564-4795/w124032%20Fault%20Memory%20Diagnosis.pdf )

Ett tips är att ladda ned det dokumentet då deras server verkar vara lite skraltig och ofta ligger nere.


Notera även att här framgår hur man nollställer adaptionen, efter att man nollat ev. felkoder.
Klistrar väl in det för säkerhetsskull:

Preconditions for test with pulse counter
Erasing fault memory

Note: Reading fault memory with the pulse counter is only possible on vehicles up to HHT diagnosis code 46. Vehicles with a diagnosis code 49 or higher (incremental control) now only possible with HHT!

D Connect pulse counter to the test coupling for diagnosis (X11/4) according to the connection diagram.
Reading and clearing DTC-codes
a) Ignition: ON
b) Press start button 2 - 4 s ("fault code" appears).
c) Read out fault code and note.
d) Press start button 6 - 8 s; the fault displayed previously is cancelled.
d) Once again press start button 2 - 4 s.
e) Read out fault code.
Repeat steps d) and e) as often as necessary until the first fault code (1)
re-appears.

Resetting and re-activating memory of HFM control unit
a) Ignition: ON
b) Press start button for 2 - 4 seconds.
Reading fault memory + Erase fault memory.
After fault code "I" appears, press the start button 6 - 8 s.
c) Switch off ignition and wait at least 2 seconds.
d) Switch on ignition and wait at least 10 seconds before starting engine.

Note:
With Bosch control units up to 8/93 it is necessary to press the start button for 5 - 6 s to cancel the faults and for 8 - 9 s to reset and reactivate the memory.

Lite felkoder, anyone?
Hittade denna rätt kompletta lista på både analoga och digitala felkoder:
www.motodok.com/Documentation/Files/mb- ... -98-00.pdf
INfon verkar stämma med Mercedes egna uppgifter.
Kopierar in en liten del för HFM bara (det finns här även koder för SRS, ABS, ASR, etc etc):

Citat:
HFM Sequential Multiport Fuel Injection - Analog
Engines Model Year
104 111 1993
See digital HFM injection section page 22 for models 3/93 and later.
Also check for codes in the Diagnostic Module (DM page 41 and 43) and the Electronic Accelerator/Cruise Control (EA/CC/ISC
pages 50 and 49).
FAULT CODE TABLE
DTC Readout Possible Cause of Failure
1 No fault found
2 Engine Coolant temperature sensor
3 Intake air temperature sensor
4 Hot film mass air flow sensor
5 CTP switch
6-7 Not used
8 Idle speed control (ISC) system at upper or lower control stop or CC or EA indicates "limp home" mode.
9 O2S 1 (before TWC) - voltage too high, circuit open or voltage implausible
10 O2S 2 (after TWC)voltage too high, circuit open or voltage implausible
11 O2S 1 heater (before TWC) - Current too high/low or short circuit.
12 O2S 2 heater (after TWC) - Current too high/low or short circuit.
13 O2S (Lambda) control system operating at rich or lean limit
14 Injector, cylinder 1
15 Injector, cylinder 2
16 Injector, cylinder 3
17 Injector, cylinder 4
18 Injector, cylinder 5
19 Injector, cylinder 6
20 Self-adaptation at idle speed or upper/lower partial load at rich or lean limit
21 Ignition output 3 or ignition coil for cylinder 1 and 6
22 Ignition output 1 or ignition coil for cylinder 2 and 5 (Engine 111, cylinder 1 and 4)
23 Ignition output 2 or ignition coil for cylinder 3 and 4 (Engine 111, cylinder 2 and 3)
24 CKP sensor or magnet for position sensor not recognized
25 CMP sensor not recognized or implausible
26 Not used
27 TN-signal (rpm signal ) - open or short to ground
28 VSS - open circuit
29 Not used
30 Fuel pump relay module - open or short circuit
31 Not used
32 Knock sensors 1 and /or 2
33 Maximum retard setting on at least one cylinder has been reached or the ignition angle deviation between the
individual cylinders is greater than 6 degrees crankshaft angle
34 Knock control-output switch in engine control module faulty Momentary fault in self-adaptation closed throttle
speed/partial load
35 Model 124,129 and 140 AIR pump switchover valve and/or electromagnetic AIR pump clutch.
Model 202 AIR pump switchover valve and/or AIR relay module
36 Purge control valve - open/short to ground or B+
37 Transmission Upshift delay switchover valve (Y3/3) without function (Logic Chain) - Check vacuum and
adjust Bowden cable.
38 Adjustable camshaft timing solenoid - open/short to ground or B+
39 Exhaust gas recirculation switchover valve - open/short to ground or B+
40 Transmission overload protection switch - open/short to ground or B+ or open or closed or implausible
41 CAN communication from engine control module faulty
20
Оборудование для автосервиса http://www.motodok.com
DTC Readout Possible Cause of Failure
42 CAN communication from ASR, EA/CC/ISC module or diagnostic module (OBD II) faulty
43 Starter signal (circuit 50) not present
44 Not used
45 Fuel safety shut-off of electronic accelerator or cruise control active
46 Resonance intake manifold switchover valve - open/short to ground or B+
48 O2S 2 (after TWC) heating circuit relay module - open/short to ground or B+
49 Voltage supply at engine control module implausible/low volts.
50 Engine control module faulty or not coded.



Se även här:
http://etanol.nu//forumrecover/viewtopic.php?t=711

_________________
http://direktdemokraterna.se
Myndigförklara dig själv.


Dela på FacebookDela på TwitterDela på TuentiDela på SonicoDela på FriendFeedDela på OrkutDela på DiggDela på MySpaceDela på DeliciousDela på TechnoratiDela på TumblrDela på Google+
Upp
 Profil  
 
Visa inlägg nyare än:  Sortera efter  
Ny tråd Svara på tråd  [ 1 inlägg ] 

Alla tidsangivelser är UTC + 1 timme


Vilka är online

Användare som besöker denna kategori: Inga registrerade användare och 2 gäster


Du kan inte skapa nya trådar i denna kategori
Du kan inte svara på trådar i denna kategori
Du kan inte redigera dina inlägg i denna kategori
Du kan inte ta bort dina inlägg i denna kategori
Du kan inte bifoga filer i denna kategori

Sök efter:
Hoppa till:  
POWERED_BY
Swedish translation by Peetra & phpBB Sweden © 2006-2011